en
en
  • Turkish
en TL
  • USD
  • EUR
  • CHF
  • GBP
menü simgesi Categories
blog simge BLOG
Actuonix

Actuonix Linear Rod Actuator, L12-50-50-12-I, Control: On-Board Microcontroller, 12V

Product Code : 03.05.005.035
5,983.08 TL + VAT
7,179.70 TL (VAT Included)
  • Features
  • Payment Options
  • Comments (0)

  • Actuonix L12-50-50-12-I Miniature Linear Rod Actuator, Control: On-Board Microcontroller ( -I ), 12V, 50mm Strok, 50:1

    Actuonix L12 linear actuator family is divided into four types based on the control method: limit switched (-S), position feedback via potentiometer (-P),  on-board microcontroller (-I) and  standard hobby type RC servo motor interface (-R). Actuonix L12-I Series linear actuators are linear actuators controlled by an on-board non-programmable microcontroller and can be utilized in 4 different modes based on the signal on its connector.  L12-I series have the following essential variations;

       o There are 3 different stroke options: 30mm, 50mm and 100mm ( 10mm is NOT Available! )

       o There are 3 different peak push-pull force for different loads such as:  22N , 42N ve 80N 

       o For the force mentioned above the no-load speeda are: 25mm/s, 13mm/s, 6.5mm/s 

       o And 2 separate supply options: 6V & 12V 

    which means 18 different actuators in the L12-I series!!!

    The L12-I series products have a built-in, software-based microcontroller. This microcontroller is not programmable and controls the actuator in the appropriate mode depending on which of the connector terminals is active at the moment of energization, these modes are;

     RC servo mode : The desired actuator position is input to the actuator as a positive 5V pulse signal from terminal 4 (no.). A 1.0 ms pulse commands the controller to fully retract the actuator. Pulse signals of 2.0 ms command full extension.
     0–5V interface mode : This mode allows the actuator to be signaled and controlled to the desired position using only a battery and potentiometer.
     4–20mA interface mode : This mode is typically compatible with PLC devices used in industrial control applications. The desired actuator position (setpoint) is input at terminal 1 (no.) as a current between 4mA and 20 mA.
     PWM mode : In PWM mode, the actuator is controlled using a single digital output pin from the external microcontroller.


    Other features of Actuonix L12-50-50-12-I linear servo actuator

    i) The actuator adjusts its position according to the desired operating mode. No LAC card is required to control Actuonix L12-I series products! In Actuonix L12-I products, low reduction ratios mean high speed but at the same time low force.

    ii) L12-I series products consist of an anodized aluminium shaft, metal gearbox, brass screws and ball bearings made of steel.

    iii) Each L12-I series linear servo motor is shipped with a mounting hardware kit consisting of clamps, brackets, nuts, rod ends, screws, etc.!

    Actuator Types in L12-I Series

    This product L12-50-50-6-I:

     L12-50-50-12-I 
    L12 50 50 12 I
    Rod Type
    Actuator    		  50mm: stroke length 50:1= gear ratio  12V Nominal supply voltage Control: via on-board microcontroller
    PWM, servo,     0-5V, 4-20mA 



    Compare this product with others in the L12-I Series:


    Gearing options

    50:1
    100:1
    210:1





    Stroke
    10mm    		 X X X

    30mm
    √
    √
    √

    50mm
    √
    √
    √

    100mm
    √
    √
    √


    L12-I Technical Features



    Gear Ratio 50:1 100:1 210:1
    Peak Power Point 17N @ 14mm/s 31N @ 7mm/s 62N @ 3.2mm/s
    Tepe Efficiency Pointı 10N @ 19mm/s 17N @ 10mm/s 36N @ 4.5mm/s
    Maximum Speed (no-load) 25 mm/s 13 mm/s 6.5 mm/s
    Maximum Force 22N 42N 80N
    Back Drive Force 12N 22N 45N

    Stroke Options
            10mm                   30mm                  50mm                   100mm
    Mass X 34g 40g 56g
    Repeatibility (-I,-R,-P) X ±0.2mm ±0.3mm ±0.5mm
    Maximum Side Load X 40N 30N 15N
    Closed Length X 82mm 102mm 152mm
    Potantiometer (-I,-R,-P) X 3kΩ/mm ± 30% 6 kΩ/mm ± 30% 11 kΩ/mm ± 30%
    Voltage Options 6V
    Maximum Input Voltage  7.5V
    Standby Current  7.2mA
    Stall Current  460mA
    Working Temperature –10°C to +50°C
    Maximum Duty cycle % 20
    Noise 55 dB,  @45 cm 
    Ingress Protection IP-54
    Mechanical Backlash 0.2mm
    Maximum Static Force 200N


    Technical Drawing

    actuonix-L12-boyutlar.jpg (139 KB)

    Links


    L12 Series Actuator Datasheet: Actuonix L12 Datasheet
    L12 Series 3D Model (IGES) 10, 30, 50 and 100mm: L12 3D Models (IGES)
    L12 Series 3D Model (STP): L12 3D Model (STP)

Prepared by  T-Soft E-Commerce.